2022 Jaguar XF X260 Left Tail Light JX6313405AF GENUINE SPORTSBRAKE LED

In stock now

We have part number JX6313405AF in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

2022 Jaguar XF X260 Left Tail Light JX6313405AF GENUINE SPORTSBRAKE LED - part number JX6313405AF

2022 Jaguar XF X260 Left Tail Light JX6313405AF GENUINE SPORTSBRAKE LED - part number JX6313405AF - view 2 2022 Jaguar XF X260 Left Tail Light JX6313405AF GENUINE SPORTSBRAKE LED - part number JX6313405AF - view 3 2022 Jaguar XF X260 Left Tail Light JX6313405AF GENUINE SPORTSBRAKE LED - part number JX6313405AF - view 4

The part we have in stock now.

About part number JX6313405AF

A rear tail light assembly forms part of the exterior lighting system on a vehicle. Located at the rear on the left-hand side, also known as the near side or passenger side, this lamp communicates the presence and width of the vehicle to following traffic in low visibility. When it is working correctly, it illuminates evenly alongside the other rear lighting functions, giving clear signals to drivers behind you.

To ensure this component is the correct replacement, you must match the manufacturer part number JX6313405AF. You may also find the secondary reference number 08061985S13 printed on the casing. Part numbers are typically stamped or printed on the rear plastic housing or mounting tags, which can be viewed once the unit is removed from the vehicle. Matching these exact numbers is the only way to confirm correct fitment.

These units are usually replaced after physical impact damage, cracks in the outer lens that allow water inside, or internal failure of the lighting components. When fitting a replacement rear lamp unit, you may need replacement plastic mounting clips, fixing screws, or fresh seals to prevent moisture ingress behind the bodywork.

  • Part type: Rear Light Assemblies.
  • Position on the vehicle: Left, Rear, passenger, ns.
  • Also numbered: 08061985S13.

About this kind of part: rear lamps

A rear lamp holds several separate functions in one housing: the tail light, the brake light, the indicator, the reversing light and the rear fog light. On most cars one lamp carries the reversing light and the other carries the rear fog light, so the two sides are not mirror images of each other in what they actually do. The light source is a bulb or a set of light-emitting diodes, and a diode lamp cannot be converted to bulbs.

Why people replace one

  • The lens has cracked, usually from a knock while reversing, and water has got into the housing.
  • The red lens has faded to pink where it has stood in the sun, which shows most on an older car.
  • A diode section has gone dark in patches, which cannot be repaired because the diodes are sealed into the unit.
  • The housing is sound but a mounting stud or lug has broken, so the lamp no longer pulls up tight against its seal and lets water past.
  • Condensation sits inside after rain, because a bulb holder seal or a breather has perished.

Fitting it

  • Most rear lamps are reached from inside the boot or the tailgate aperture, behind a trim panel or a removable cover.
  • The lamp is held by two or three nuts on studs and then pulls straight back out of its locating pegs.
  • The foam or rubber seal around the back of the lamp is what keeps water out of the boot. If it has hardened, water will find its way in whatever else is done.
  • On a car with diode lamps the car may watch the current drawn by each function, so a mismatched unit can log a fault.

Making sure it is the right one

  • Match the part number, not the side of the car. The reversing light and the rear fog light sit on opposite sides, and markets that drive on the left put them the other way round from markets that drive on the right, so a lamp can look like the wrong side and still be the correct part.
  • A bulb lamp and a diode lamp for the same model share the aperture and will bolt in, but the car will not operate them correctly and the connector differs.
  • Count the connector pins and compare the block shape with your own lamp.
  • Compare the pattern of the lens sections. A facelift often reshapes the internal pattern while keeping the outer shape, so the number is the only reliable test.

What to look for in the photographs

A Part number — On a printed label on the back of the housing, or moulded into the plastic near the connector.
B Connector block — The plug on the back. Count the pins and compare the shape, because a bulb unit and a diode unit differ here.
C Function layout — Which section is the reversing light and which is the rear fog light. These sit on opposite sides of the car, and the other way round in markets that drive on the other side of the road.
D Mounting studs and lugs — The threaded studs and locating pegs on the back. A broken one means the lamp cannot be pulled tight against its seal.
E Seal face — The foam or rubber seal around the back edge. This is what keeps water out of the boot.
F Lens surface — Look at the lens at an angle rather than straight on, which shows up fine crazing and any fading that a flat photograph hides.

This section describes rear lamps parts in general. The numbers and the photographs above are this part.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Jaguar part number we list · All part numbers · Everything in stock now