AUDI A1 8X MK1 FL REAR BUMPER WHITE 8XA807511

In stock now

We have part number 8XA807511 in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

About part number 8XA807511

A rear bumper cover forms the outer body panel at the rear of the vehicle, protecting the underlying crash structures and parking sensors while giving the back of the car its finished appearance. It mounts directly to the rear panel and side support brackets, framing the rear lights and lower trim. When properly fitted, it aligns smoothly with the surrounding wings and tailgate.

To confirm that this replacement bumper is correct for your vehicle, you must check that your existing part displays the exact part number 8XA807511. On an exterior panel of this type, the part number is typically stamped or moulded into the inner plastic surface on the reverse side. Matching this specific number is the only way to guarantee correct fitment and panel alignment.

A rear bumper is usually replaced after receiving impact damage from a collision or light damage from reversing into an obstacle. When fitting a replacement bumper cover, you often need replacement plastic mounting clips, fixing screws, and occasionally new parking sensor brackets or trim clips if the original fixings broke during removal.

• Part type: Bumpers & Reinforcements.
• Specification: donor car id 442; tag reference 32403; engine code CXMA; engine number CXMA040144; our part number 32394; sku code 32403; number of doors 3; engine size 1598; driver side Right; donor car year 2016.
• Position on the vehicle: Rear.

About this kind of part: bumper covers

A bumper cover is the painted plastic skin across the front or the rear of a car. It is not a structural part. Behind it sit a foam or honeycomb absorber and a steel or aluminium reinforcement bar, and those are what take an impact. The cover carries the grille apertures, the number plate plinth and the openings for parking sensors, washer jets and tow eyes, so one model can take several different covers depending on how it was specified when new.

Why people replace one

• A knock in a car park or a light collision has cracked or torn the plastic. A tear can be plastic-welded, but it rarely returns to a finish that will take paint without showing.
• The paint has faded or crazed differently from the panels around it. A bumper flexes and sits low in the spray from the road, so it ages faster than a wing.
• The mounting tabs along the top edge or inside the wheel arches have snapped, so the cover stands proud of the panel next to it.
• An earlier repair has been filled and has begun to lift.

Fitting it

• It is held by screws along the top edge, screws or clips inside each wheel arch, and plastic nuts underneath the car.
• Lamps, grilles, sensors, washer jets and the number plate plinth usually move across from the old cover.
• A cover is supplied either in primer or in the colour it was sprayed when new. A matching finish needs the paint code from the car's own identification plate.
• Parking sensors go back into their own openings, and the trim rings around them are often specific to the colour.

Making sure it is the right one

• Match the part number moulded into the old cover rather than matching the shape. A facelift changes the number while the outline can look almost the same.
• Check whether the car has parking sensors. A cover with no sensor openings cannot be used on a car that has them, and drilling one is not a repair.
• Count the openings and compare them: fog lamp apertures, the tow eye cover and any camera or washer cut-out differ between trim levels on the same model.

What to look for in the photographs

This section describes bumper covers parts in general. The numbers and the photographs above are this part.

Parts we have that go with this one

Most repairs need more than one part, and these came off the same area of the vehicle. Each has its own page, which says whether we have one in stock today.

• A1 front bumper right side grill cover on 82A853506
• A1 8X Rear Bumper Centre Mounting Bracket Genuine 8X0807385
• A1 SE REAR BUMPER ONWARDS 82A807511A GENUINE WITH DIFFUSER SPOILER
• A1 Sportback GB 35 TFSI Rear Right Bumper Bracket Holder 82A807394
• Bumper Carrier Reinforcement A1 Sportback Rear 82A807308
• NEW A1 GB REAR RIGHT DOOR INNER PANEL COVER 82G839916 ORIGINAL

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

• 2019-2025 AUDI A1 MK2 18" ALLOY WHEEL & TYRE 215/40/18 82A601025Q KR2
• Audi A1 8X 2010-2018 Rear Bumper Centre Mounting Bracket Genuine 8X0807385
• AUDI A1 S LINE 2018-ON FRONT BUMPER MAIN GRILLE 1433 82A853653B
• AUDI A1 S LINE 2018 - 2026 GENUINE 18" DIAMOND CUT ALLOY 7.5J 46ET 82A601025AB
• AUDI A1 SE REAR BUMPER 2018 ONWARDS 82A807511A GENUINE WITH DIFFUSER SPOILER
• AUDI A1 Sportback GB 35 TFSI Rear Right Bumper Bracket Holder 82A807394
• AUDI A1 Sportback GB Rear Right Tail Light 82A945092C 2023 RHD 26338564
• AUDI A3 8P 04-12 HATCH RIGHT REAR BUMPER SUPPORT BRACKET MOUNT 8P4807378B
• AUDI A3 8V 2018 RHD Rear Parcel Shelf Load Cover Panel 8V5863411F 3249917
• Audi A3 8Y 2023 Rear Towing Eye Hook Cap Cover Trim 8Y4807441A AMD121626

See every Audi part number we list · All part numbers · Everything in stock now