Audi Q2 S Line 2016-2020 Rear Bumper Upper Skin PDC 81A807511B

In stock now

We have part number 81A807511B in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

About part number 81A807511B

A rear bumper upper skin forms the main exterior panel at the back of the car's bodywork. It attaches to the vehicle structure and surrounding body panels, providing an aerodynamic outer surface while protecting internal components. It also houses parking sensor mounts (PDC), allowing the parking assistance system to operate correctly and alerting the driver to obstacles when reversing.

To confirm this part will fit your vehicle, you must check that the part number matches your original item. Look for the part number stamped or printed on the inner surface or mounting flange of your original bumper skin. The correct manufacturer part numbers to match for this item are 81A807511B and 81A807511. Matching the exact part number is the only way to guarantee correct fitment.

When replacing a bumper skin, installers often need fresh mounting clips, plastic rivets, or parking sensor retainers, as these original fasteners often break during removal. This type of panel is usually replaced due to cosmetic damage, cracks, or impact damage from low-speed collisions.

• Part type: Bumpers & Reinforcements.
• Specification: colour Ara Blue.
• Also numbered: 81A807511.

About this kind of part: bumper covers

A bumper cover is the painted plastic skin across the front or the rear of a car. It is not a structural part. Behind it sit a foam or honeycomb absorber and a steel or aluminium reinforcement bar, and those are what take an impact. The cover carries the grille apertures, the number plate plinth and the openings for parking sensors, washer jets and tow eyes, so one model can take several different covers depending on how it was specified when new.

Why people replace one

• A knock in a car park or a light collision has cracked or torn the plastic. A tear can be plastic-welded, but it rarely returns to a finish that will take paint without showing.
• The paint has faded or crazed differently from the panels around it. A bumper flexes and sits low in the spray from the road, so it ages faster than a wing.
• The mounting tabs along the top edge or inside the wheel arches have snapped, so the cover stands proud of the panel next to it.
• An earlier repair has been filled and has begun to lift.

Fitting it

• It is held by screws along the top edge, screws or clips inside each wheel arch, and plastic nuts underneath the car.
• Lamps, grilles, sensors, washer jets and the number plate plinth usually move across from the old cover.
• A cover is supplied either in primer or in the colour it was sprayed when new. A matching finish needs the paint code from the car's own identification plate.
• Parking sensors go back into their own openings, and the trim rings around them are often specific to the colour.

Making sure it is the right one

• Match the part number moulded into the old cover rather than matching the shape. A facelift changes the number while the outline can look almost the same.
• Check whether the car has parking sensors. A cover with no sensor openings cannot be used on a car that has them, and drilling one is not a repair.
• Count the openings and compare them: fog lamp apertures, the tow eye cover and any camera or washer cut-out differ between trim levels on the same model.

What to look for in the photographs

This section describes bumper covers parts in general. The numbers and the photographs above are this part.

Parts we have that go with this one

Most repairs need more than one part, and these came off the same area of the vehicle. Each has its own page, which says whether we have one in stock today.

• Q2 S-LINE rear bumper bottom part genuine 81A807323 | Part number 81A807323A
• Q2 ONWARDS S LINE GENUINE REAR BUMPER 81A807511C diffuser
• Q2 Front Bumper Right Tow Cover ON 81A807241A Genuine
• Q2 GA Front Bumper Lower Centre Grille No PDC 81A807647D
• Q2 MK1 RIGHT HEADLIGHT HALOGEN 81A941004A (2348)
• Q2 RIGHT Door Moulding Trim GENUINE Used 81A853970A
• Q2 S Line Front Left Door Moulding TO 81A853959A Genuine THE BEST
• GENUINE Q2 REAR BUMPER TOW EYE COVER - ON 81A807441E

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

• Audi Q2 S Line Rear Left Side Door Moulding 2016 TO 2021 81A853969A Genuine
• Audi Q2 wheel arch trim left rear genuine 81A853817A
• AUDI Q3 8U Front Bumper Right Tow Eye Cover 8U0807241DT94 2015on
• Audi Q3 Rear Right Wheel Arch 2017 ON 83A853818A Genuine
• Audi Q3 Rear Wheel Arch Trim Grey LH UK Passenger Side 2011-18 MK1 8U0853817A
• AUDI Q3 S-LINE 2018-23 RIGHT FRONT GRILLE 83A807682D GENUINE
• AUDI Q3 8U S-LINE 2015-2017 GENUINE DIFFUSER LOWER REAR BUMPER 8U0807521AQ
• AUDI Q3 S-LINE 2018-2023 GENUINE FRONT BUMPER GRILLE 83A853651B
• Audi Q3 S line Left side LED Headlight 2018 on 83A941033A Genuine
• AUDI Q3 S-LINE REAR BACK BUMPER 8U0807511C 8U0807521H 2011-2015

See every Audi part number we list · All part numbers · Everything in stock now