GENUINE Ford Kuga 12-16 Left Fog Lamp Cv4413b221bg EXCELLENT CONDITION

In stock now

We have part number CV4413B221BG in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

GENUINE Ford Kuga 12-16 Left Fog Lamp Cv4413b221bg EXCELLENT CONDITION - part number CV4413B221BG

GENUINE Ford Kuga 12-16 Left Fog Lamp Cv4413b221bg EXCELLENT CONDITION - part number CV4413B221BG - view 2 GENUINE Ford Kuga 12-16 Left Fog Lamp Cv4413b221bg EXCELLENT CONDITION - part number CV4413B221BG - view 3 GENUINE Ford Kuga 12-16 Left Fog Lamp Cv4413b221bg EXCELLENT CONDITION - part number CV4413B221BG - view 4

The part we have in stock now.

About part number CV4413B221BG

A fog lamp assembly provides extra illumination in low-visibility driving conditions such as heavy fog, mist, or rain. Positioned on the left-hand side of the front bumper, this light sits lower down than a main headlight unit to cast a wide beam along the road surface without reflecting glare back towards the driver. When the switch is turned on, it helps the driver see lane markings and kerbs more clearly in poor weather.

To confirm this part is correct for your vehicle, check that the original unit matches the manufacturer part number CV4413B221BG. On a fog light assembly, this code is typically stamped or printed directly onto the plastic rear housing or the outer casing. Matching this exact number is the only way to guarantee a correct fit.

These units are usually replaced due to damage from flying road debris, cracked glass lenses, or moisture entering the housing and causing corrosion. When installing a replacement unit, you may also need new fixing screws and a replacement bulb if your existing one is damaged or blown.

  • Part type: Fog Light Assemblies.
  • Specification: mounting style Screws.
  • Position on the vehicle: Left.

About this kind of part: fog lamps

A fog lamp is a small sealed unit set into the lower corner of a front bumper, below the main headlamp. Its beam is wide and flat and cut off sharply at the top, which is what stops it reflecting back off fog, and that pattern is why it cannot be substituted with any other kind of lamp. On many cars the same housing also provides the cornering light that illuminates the direction the wheels are turned, and on some it is a daytime running light as well.

Why people replace one

  • A stone has broken the lens, which is almost inevitable on a lamp mounted this low and this far forward.
  • The housing has cracked or the mounting tabs have snapped in a light knock, because the fog lamp sits exactly where a bumper takes a kerb or a post.
  • Water has got into the unit through a failed seal and the lens mists up or the lamp has corroded internally.
  • The lens has clouded and yellowed from stone blasting and road salt.
  • The lamp has been removed for a bumper repair and the tabs were broken getting it out.

Fitting it

  • Most fog lamps are reached from behind the bumper cover, sometimes through the wheel arch liner and sometimes only with the bumper off.
  • They are held by two or three screws into a carrier, or clipped into a surround that is itself screwed to the bumper.
  • The aim is adjustable on most units and is set low and level. A fog lamp aimed upwards defeats its own purpose and dazzles.
  • The surround or finisher around the lamp is usually a separate part, and it is often what was broken rather than the lamp itself.

Making sure it is the right one

  • Match the part number. Within one model there are commonly a plain fog lamp, one that also provides a cornering light, and a diode version, and they are not interchangeable.
  • Count the connector pins and compare the block with your own lamp. A lamp with extra functions has extra wires.
  • Check the lens marking against your own. It records the approval and the beam type, and a lamp of the wrong type is not a legal substitute.
  • Compare the mounting arrangement: some clip into a surround and some screw to a carrier, and the two cannot be swapped.

What to look for in the photographs

A Part number — On a label or moulded into the back of the housing.
B Lens marking — Etched into the lens: the approval and the beam type. Compare it with the marking on your own lamp.
C Connector — Count the pins. A plain fog lamp, one with a cornering light and a diode unit all differ here.
D Mounting tabs — The tabs or screw bosses that hold the lamp. These snap easily and are the most common hidden fault.
E Lens surface — Look across the lens at an angle. Stone pitting on a lamp this low shows in a raking light and disappears in a flat one.
F Seal and housing — The joint where the lens meets the housing, and the back cover. Water enters where these have been disturbed.

This section describes fog lamps parts in general. The numbers and the photographs above are this part.

Parts we have that go with this one

Most repairs need more than one part, and these came off the same area of the vehicle. Each has its own page, which says whether we have one in stock today.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Ford part number we list · All part numbers · Everything in stock now