GRILLE BUMPER FRONT Land Rover DISCOVERY sport l550 mk72-17h750 2018on

In stock now

We have part number MK72-17H750 in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

GRILLE BUMPER FRONT Land Rover DISCOVERY sport l550 mk72-17h750 2018on - part number MK72-17H750

GRILLE BUMPER FRONT Land Rover DISCOVERY sport l550 mk72-17h750 2018on - part number MK72-17H750 - view 2 GRILLE BUMPER FRONT Land Rover DISCOVERY sport l550 mk72-17h750 2018on - part number MK72-17H750 - view 3 GRILLE BUMPER FRONT Land Rover DISCOVERY sport l550 mk72-17h750 2018on - part number MK72-17H750 - view 4

The part we have in stock now.

About part number MK72-17H750

A front bumper grille is an exterior bodywork component that forms part of the front bumper assembly. It covers an opening in the vehicle bumper, allowing airflow through to the radiator and engine bay to aid cooling, while protecting internal components from road debris. When it is intact and correctly fitted, it keeps the front end looking tidy and helps maintain proper airflow to the cooling system.

To confirm that this part is correct for your vehicle, you must check that your original part number matches MK72-17H750. On a plastic bumper grille like this, the part number is usually stamped or moulded directly into the plastic on the back or inner edge of the component. Matching this exact number is what determines if the part will fit correctly.

These grilles are commonly replaced because of impact damage from low-speed collisions, parking accidents, or stone chips and cracks caused by flying road debris. When replacing a front bumper grille, a person usually needs plastic trim clips or fixing screws to secure it properly, and in some cases, the front bumper cover must be partially unbolted to access the mountings.

  • Part type: Bumpers & Reinforcements.
  • Specification: country of origin United Kingdom.
  • Position on the vehicle: Front.

About this kind of part: grilles

A grille is the moulded panel across the front of a car that lets air through to the radiator and carries the maker's badge. On a modern car it is rarely one piece: there is usually an upper grille set into the bonnet line, a lower grille in the bumper cover, and separate side inserts. Many now also hold the forward radar, a camera or the active shutters that close off the airflow, so the same model can take several different grilles depending on what was specified when new.

Why people replace one

  • A stone or a light knock has broken one of the slats, which cannot be glued back without showing.
  • The chrome or bright finish on the surround has lifted and started to flake, which spreads once the plating is broken.
  • The clips along the back have snapped, so the grille stands away from the bumper cover at one corner.
  • A badge mount has broken and the badge no longer sits flat.
  • The gloss black finish has gone dull and grey from washing and road grit.

Fitting it

  • A grille is usually held by clips around its edge and a few screws reached from behind, which often means taking the bumper cover off to reach them.
  • The badge, any surround trim and the radar or camera bracket normally transfer from the old grille.
  • Work the clips from behind rather than pulling on the slats, which break easily when cold.
  • If the grille carries a radar or a camera, that unit will usually need aiming or calibrating after it is disturbed.

Making sure it is the right one

  • Match the part number moulded on the back. A grille from a different trim level will clip in and sit correctly while being the wrong pattern or the wrong finish.
  • Check whether the grille has an opening or a mount for a radar or a camera. One without the mount cannot carry the unit, and one with it looks wrong on a car that has none.
  • Compare the finish as well as the shape: the same grille is made in gloss black, in a bright finish and in body colour, and these are separate part numbers.
  • Count the fixing points and compare their positions with your own grille before buying.

What to look for in the photographs

A Part number — Moulded into the back of the frame, often near an edge. This is the number to match.
B Radar or camera mount — An opening, a bracket or a blanking panel behind the badge. Compare it with your own grille, because this is what varies most between trim levels.
C Clips and mounting tabs — The row of clips and tabs around the back edge. Count them and look for any that are broken.
D Badge mount — The seat the maker's badge fits into. The badge is a separate part.
E Slats and mesh — Look along the slats rather than at them, which shows a cracked or missing one that a flat photograph hides.
F Surround finish — The outer frame: bright, gloss black or body colour. The finish is part of what you are matching.

This section describes grilles parts in general. The numbers and the photographs above are this part.

Parts we have that go with this one

Most repairs need more than one part, and these came off the same area of the vehicle. Each has its own page, which says whether we have one in stock today.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Land Rover part number we list · All part numbers · Everything in stock now