Range Rover Evoque 2018 RIGHT Fog Grill P/N GJ3215A298B Genuine NEXT DAY DELIVER

Part number GJ3215A298B. We take parts off vehicles every week, and this page is updated with a link straight to the part as soon as another one arrives.

OUT OF STOCK

In the meantime you can see every Land Rover part we have in stock, or you can send us a message and we will tell you the day one comes in.

Notify me when this part is back in stock

Leave your email address and we will write to you the day part number GJ3215A298B comes in. We use your address for that message only.

About part number GJ3215A298B

A fog light grille is an exterior trim piece located on the front bumper. It surrounds the front fog lamp, protecting the lamp housing and securing it within the bumper assembly while allowing airflow to surrounding components. When the part is intact, it gives the front end of the vehicle a neat, finished appearance and keeps the fog lamp aligned correctly.

To confirm that this is the correct part for your vehicle, you must match the part number GJ3215A298B exactly with the number stamped on your original item. On plastic bumper trims and grilles, the part number is usually moulded or stamped into the plastic on the reverse side. Matching this exact reference number is the only way to guarantee a correct fit.

People usually replace this trim because it has been cracked in a low-speed parking impact, damaged by road debris, or lost entirely. When fitting a replacement fog light grille, you may also need replacement plastic bumper clips, fasteners, or a new fog light unit if the original lamp was damaged in the same incident.

About this kind of part: grilles

A grille is the moulded panel across the front of a car that lets air through to the radiator and carries the maker's badge. On a modern car it is rarely one piece: there is usually an upper grille set into the bonnet line, a lower grille in the bumper cover, and separate side inserts. Many now also hold the forward radar, a camera or the active shutters that close off the airflow, so the same model can take several different grilles depending on what was specified when new.

Why people replace one

  • A stone or a light knock has broken one of the slats, which cannot be glued back without showing.
  • The chrome or bright finish on the surround has lifted and started to flake, which spreads once the plating is broken.
  • The clips along the back have snapped, so the grille stands away from the bumper cover at one corner.
  • A badge mount has broken and the badge no longer sits flat.
  • The gloss black finish has gone dull and grey from washing and road grit.

Fitting it

  • A grille is usually held by clips around its edge and a few screws reached from behind, which often means taking the bumper cover off to reach them.
  • The badge, any surround trim and the radar or camera bracket normally transfer from the old grille.
  • Work the clips from behind rather than pulling on the slats, which break easily when cold.
  • If the grille carries a radar or a camera, that unit will usually need aiming or calibrating after it is disturbed.

Making sure it is the right one

  • Match the part number moulded on the back. A grille from a different trim level will clip in and sit correctly while being the wrong pattern or the wrong finish.
  • Check whether the grille has an opening or a mount for a radar or a camera. One without the mount cannot carry the unit, and one with it looks wrong on a car that has none.
  • Compare the finish as well as the shape: the same grille is made in gloss black, in a bright finish and in body colour, and these are separate part numbers.
  • Count the fixing points and compare their positions with your own grille before buying.

What to look for in the photographs

A Part number — Moulded into the back of the frame, often near an edge. This is the number to match.
B Radar or camera mount — An opening, a bracket or a blanking panel behind the badge. Compare it with your own grille, because this is what varies most between trim levels.
C Clips and mounting tabs — The row of clips and tabs around the back edge. Count them and look for any that are broken.
D Badge mount — The seat the maker's badge fits into. The badge is a separate part.
E Slats and mesh — Look along the slats rather than at them, which shows a cracked or missing one that a flat photograph hides.
F Surround finish — The outer frame: bright, gloss black or body colour. The finish is part of what you are matching.

This section describes grilles parts in general. The numbers and the photographs above are this part.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Land Rover part number we list · All part numbers · Everything in stock now