Skoda Fabia IV 2022 On Right Front Air Guide Duct 6VA121764 Genuine

In stock now

We have part number 6VA121764 in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

Skoda Fabia IV 2022 On Right Front Air Guide Duct 6VA121764 Genuine - part number 6VA121764

Skoda Fabia IV 2022 On Right Front Air Guide Duct 6VA121764 Genuine - part number 6VA121764 - view 2 Skoda Fabia IV 2022 On Right Front Air Guide Duct 6VA121764 Genuine - part number 6VA121764 - view 3 Skoda Fabia IV 2022 On Right Front Air Guide Duct 6VA121764 Genuine - part number 6VA121764 - view 4

The part we have in stock now.

About part number 6VA121764

An air guide duct is a plastic cooling component that channels incoming air directly through the front bumper toward the radiator and engine bay. Situated on the right-hand side at the front of the vehicle, it sits between the outer grille and the inner cooling package. When it is working correctly, it maintains proper airflow, helping the engine stay at its normal operating temperature while driving.

To confirm that this component is correct for your vehicle, you must check the part number stamped directly onto the plastic body of your existing unit. Look for the main reference number 6VA121764 or the alternative number 6VA121764A. Matching one of these exact numbers is the only way to guarantee that the replacement will fit your vehicle correctly.

These ducts are usually replaced after front-end impacts or low-speed parking bumps that crack the rigid plastic or snap off its mounting clips. When replacing this part, you often need replacement plastic rivet clips or screws to secure it safely to the surrounding bodywork and bumper supports.

  • Part type: Other Engine Cooling Components.
  • Position on the vehicle: Front, Right.
  • Also numbered: 6VA121764A.

About this kind of part: wheel arch liners

A wheel arch liner is the moulded plastic or felted shell inside a wheel arch that keeps water, salt and stones off the inner wing, the suspension and the wiring. It is hidden and it is not structural, but it is the part that decides whether the metal behind it rusts, so a missing or torn liner is a slow problem rather than a cosmetic one. Mudflaps, undertrays and the air ducts that feed the brakes are the same kind of part doing the same job elsewhere under the car.

Why people replace one

  • The liner has torn away from its clips, usually after a wheel has picked it up at speed, and it now rubs the tyre.
  • Road debris or a kerb has split the liner along an edge.
  • The clips and screws have rusted away or pulled through, so the liner hangs down and catches.
  • The liner was removed for a repair and never refitted, which leaves the inner wing exposed.
  • A felted liner has become waterlogged and heavy and has pulled itself off its fixings.

Fitting it

  • The wheel normally has to come off, and the car must be supported properly on axle stands rather than a jack alone.
  • A liner is held by a mixture of plastic screws, clips and expanding rivets around its edge, and most of them break on removal, so a set of fixings is worth having before starting.
  • Fit the fixings loosely around the whole edge first and tighten them afterwards, otherwise the last few holes will not line up.
  • With the liner out, it is worth looking at the metal behind it. A liner that has been missing for a while has usually exposed something worth seeing.

Making sure it is the right one

  • Match the part number moulded into the liner. Front and rear differ, the two sides differ, and a model with wider arches takes a different part again.
  • Count the fixing holes and compare their positions with the old liner. This is the quickest way to tell two similar liners apart.
  • Check whether yours has cut-outs or ducts for brake cooling, a sensor or a washer line. These vary by specification.
  • Compare the material. The same position is made as hard plastic on one version and as a felted shell on another, and they use different fixings.

What to look for in the photographs

A Part number — Moulded into the inner face. It is often the only difference between two liners that look the same.
B Fixing holes — The holes, slots and rivet points around the edge. Count them and compare the spacing with your own liner.
C Cut-outs and ducts — Any opening for brake cooling, a sensor or a washer line. These vary by specification and are part of the match.
D Edge condition — Look along the whole rim, particularly where the fixings pass through. This is where a liner tears out.
E Material — Hard plastic or a felted shell. They are not interchangeable and they take different fixings.

This section describes wheel arch liners parts in general. The numbers and the photographs above are this part.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Skoda part number we list · All part numbers · Everything in stock now