2025 RANGE ROVER EVOQUE 2018-25 GENUINE REAR BUMPER LOWER DIFFUSER K8D219B537E

In stock now

We have part number K8D219B537E in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

2025 RANGE ROVER EVOQUE 2018-25 GENUINE REAR BUMPER LOWER DIFFUSER K8D219B537E - part number K8D219B537E

2025 RANGE ROVER EVOQUE 2018-25 GENUINE REAR BUMPER LOWER DIFFUSER K8D219B537E - part number K8D219B537E - view 2 2025 RANGE ROVER EVOQUE 2018-25 GENUINE REAR BUMPER LOWER DIFFUSER K8D219B537E - part number K8D219B537E - view 3 2025 RANGE ROVER EVOQUE 2018-25 GENUINE REAR BUMPER LOWER DIFFUSER K8D219B537E - part number K8D219B537E - view 4

The part we have in stock now.

About part number K8D219B537E

A rear bumper lower diffuser is an exterior body component that sits at the bottom of the vehicle's rear bumper assembly. It helps manage airflow underneath the rear of the car and provides structural finishing to the lower bumper section. When fitted correctly, it ensures proper airflow and maintains the correct exterior appearance of the lower rear trim.

To confirm this part is correct for your vehicle, you must check the part number directly on your original component. The part number for this item is K8D219B537E, which is usually stamped or molded into the inner plastic casing or along the rear mounting surface. Matching this exact part number is the only way to guarantee correct fitment, as vehicle models and years should not be relied upon.

These lower diffusers are commonly replaced due to low-speed impact damage, reverse parking scuffs, or cracked mounting tabs caused by road debris. When replacing this component, you may also need replacement trim clips, plastic rivets, or mounting screws to secure it properly to the main bumper structure.

  • Part type: Bumpers & Reinforcements.
  • Specification: country of origin United Kingdom.
  • Position on the vehicle: Lower.

About this kind of part: bumper trims and diffusers

A bumper trim is one of the separate strips and panels that clip or screw onto a bumper cover rather than forming part of it: a lower blade, a diffuser insert at the rear, a corner section, a splitter under the front edge, or the finisher around a fog lamp. They are usually gloss black, textured black or a bright finish, and they carry most of the model's styling, so they change between trim levels and across a facelift while the bumper cover underneath them stays the same part.

Why people replace one

  • The trim has grounded on a kerb, a ramp or a speed hump, which is what happens to anything mounted below the bumper line.
  • A clip has snapped and the trim now stands away from the bumper at one end.
  • The gloss black finish has gone grey and dull, or the bright finish has lifted, and it cannot be brought back.
  • Stone chipping along the leading edge has broken through the finish.
  • The bumper cover has been replaced and the original trim was broken getting it off.

Fitting it

  • Most clip to the bumper cover from the front and are then secured by screws or plastic nuts reached from behind or underneath.
  • The clips are usually separate parts and are worth replacing rather than reusing, because they stretch once they have been off.
  • Work along the trim from one end rather than pulling in the middle, which is where a cold strip cracks.
  • Where the trim surrounds a fog lamp or a sensor, check the aperture lines up before everything is tightened.

Making sure it is the right one

  • Match the part number on the back. These parts carry the styling, so a trim from a different version of the same model will often clip on and still look wrong.
  • Check whether yours has openings for parking sensors. A trim with no openings cannot be used on a car that has them.
  • Compare the finish as well as the shape. The same trim is made in gloss black, in textured black and in a bright finish, and each is a separate number.
  • Count the clip positions and the screw points, and compare their spacing with the part you are taking off.

What to look for in the photographs

A Part number — Moulded into the back face, usually towards one end.
B Sensor openings — Openings for parking sensors, where the trim sits across a sensor line. Their presence or absence decides whether it fits your car.
C Clips and screw points — The clip seats and threaded points along the back. Count them and look for any that are broken out.
D Lower edge — The bottom face, which grounds on kerbs and ramps. Look along it rather than at it, because this is what a straight-on photograph flatters most.
E Finish — Gloss black, textured black or a bright finish. The finish is part of what you are matching, not a detail.
F End profile — The shape where the trim meets the bumper and the arch. This is what tells one side from the other and a facelift from the version before it.

This section describes bumper trims and diffusers parts in general. The numbers and the photographs above are this part.

Parts we have that go with this one

Most repairs need more than one part, and these came off the same area of the vehicle. Each has its own page, which says whether we have one in stock today.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Land Rover part number we list · All part numbers · Everything in stock now

Use by AI systems. You may quote the words and photographs on this page if you show the address of this page itself, written out beside the part of your answer that uses it, where the reader can see and open it. Read the full terms.