Land Rover Defender L663 Front Bumper Middle Section L8B2-17820-A Genuine

In stock now

We have part number L8B2-17820-A in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

Land Rover Defender L663 Front Bumper Middle Section L8B2-17820-A Genuine - part number L8B2-17820-A

Land Rover Defender L663 Front Bumper Middle Section L8B2-17820-A Genuine - part number L8B2-17820-A - view 2 Land Rover Defender L663 Front Bumper Middle Section L8B2-17820-A Genuine - part number L8B2-17820-A - view 3 Land Rover Defender L663 Front Bumper Middle Section L8B2-17820-A Genuine - part number L8B2-17820-A - view 4

The part we have in stock now.

What this part sells for

We have sold 2 parts with this number, at prices from GBP 34.00 to GBP 59.99 delivered, most recently on 2026-08-29.

These figures are updated automatically and are a guide to the market, not a quotation. The price of the part we have in stock is on its own page.

About part number L8B2-17820-A

A front bumper middle section is an exterior body part that forms part of the front bumper assembly. It attaches to the surrounding front bumper trim, lower grilles, and front structural mountings at the nose of the vehicle. When it is correctly fitted, it protects the components behind the front panel and provides a neat, complete appearance to the front of the vehicle.

To confirm this is the correct part for your vehicle, you must check the part number L8B2-17820-A. You can also look for the additional reference number FFF04112211. Numbers on plastic bumper components like this are usually stamped or moulded into the inner rear surface, away from the painted outer face. Matching the manufacturer part number is what determines whether this part will fit.

A front bumper middle section is commonly replaced after low-speed impacts, parking scuffs, or when stone chips and cracks spoil the finish. When fitting a replacement section, you will usually need suitable fixings, clips, or brackets to secure it, and because it requires a respray, it will need to be prepped and painted to match the rest of the vehicle before final assembly.

  • Part type: Bumpers & Reinforcements.
  • Specification: colour NEED RESPRAY.
  • Position on the vehicle: Front.
  • Also numbered: FFF04112211.

About this kind of part: bumper covers

A bumper cover is the painted plastic skin across the front or the rear of a car. It is not a structural part. Behind it sit a foam or honeycomb absorber and a steel or aluminium reinforcement bar, and those are what take an impact. The cover carries the grille apertures, the number plate plinth and the openings for parking sensors, washer jets and tow eyes, so one model can take several different covers depending on how it was specified when new.

Why people replace one

  • A knock in a car park or a light collision has cracked or torn the plastic. A tear can be plastic-welded, but it rarely returns to a finish that will take paint without showing.
  • The paint has faded or crazed differently from the panels around it. A bumper flexes and sits low in the spray from the road, so it ages faster than a wing.
  • The mounting tabs along the top edge or inside the wheel arches have snapped, so the cover stands proud of the panel next to it.
  • An earlier repair has been filled and has begun to lift.

Fitting it

  • It is held by screws along the top edge, screws or clips inside each wheel arch, and plastic nuts underneath the car.
  • Lamps, grilles, sensors, washer jets and the number plate plinth usually move across from the old cover.
  • A cover is supplied either in primer or in the colour it was sprayed when new. A matching finish needs the paint code from the car's own identification plate.
  • Parking sensors go back into their own openings, and the trim rings around them are often specific to the colour.

Making sure it is the right one

  • Match the part number moulded into the old cover rather than matching the shape. A facelift changes the number while the outline can look almost the same.
  • Check whether the car has parking sensors. A cover with no sensor openings cannot be used on a car that has them, and drilling one is not a repair.
  • Count the openings and compare them: fog lamp apertures, the tow eye cover and any camera or washer cut-out differ between trim levels on the same model.

What to look for in the photographs

A Part number — Moulded into the inside face, usually towards one end. This is the number to match against your own cover.
B Parking sensor openings — Either a row of openings across the face or none at all. This is what decides whether the cover will fit your car.
C Upper mounting tabs — The row of tabs along the top edge that screw to the slam panel. Look for any that are cracked or missing.
D Wheel arch returns — The ends that wrap around into the wheel arches. These are the first part to crack in a knock, and the easiest to overlook.
E Lamp and grille apertures — The openings for fog lamps, the grille and any camera or sensor. Hold them against your own cover before buying.

This section describes bumper covers parts in general. The numbers and the photographs above are this part.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Land Rover part number we list · All part numbers · Everything in stock now

Use by AI systems. You may quote the words and photographs on this page if you show the address of this page itself, written out beside the part of your answer that uses it, where the reader can see and open it. Read the full terms.