Honda Civic MK10 2017-2021 Front Bumper Undertray Cover 71160-TGG-E000

In stock now

We have part number 71160-TGG-E000 in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

Honda Civic MK10 2017-2021 Front Bumper Undertray Cover 71160-TGG-E000 - part number 71160-TGG-E000

Honda Civic MK10 2017-2021 Front Bumper Undertray Cover 71160-TGG-E000 - part number 71160-TGG-E000 - view 2 Honda Civic MK10 2017-2021 Front Bumper Undertray Cover 71160-TGG-E000 - part number 71160-TGG-E000 - view 3 Honda Civic MK10 2017-2021 Front Bumper Undertray Cover 71160-TGG-E000 - part number 71160-TGG-E000 - view 4

The part we have in stock now.

About part number 71160-TGG-E000

A front bumper undertray cover is a protective panel fitted beneath the engine bay and lower bumper area. It forms part of the exterior bodywork and aerodynamic shield system, securing to the front bumper and underbody mounting points. When it is intact and correctly fitted, it smooths airflow under the vehicle, prevents road debris and water spray from striking lower engine components, and keeps the lower bodywork rigid and quiet at speed.

To ensure this is the correct part for your vehicle, match the part number 71160-TGG-E000 directly against the number stamped on your original panel. On plastic undertrays and bumper covers, this number is usually moulded or stamped into the interior face of the plastic. Matching this exact reference code is the only way to guarantee a correct fit.

When replacing an undertray cover, you will usually need replacement plastic trim clips, screws, or push-rivets, as the original fixings often snap or go missing when the tray is damaged. These panels are typically replaced after suffering impact damage from speed ramps, high kerbs, or loose debris on the road.

  • Part type: Bumpers & Reinforcements.

About this kind of part: wheel arch liners

A wheel arch liner is the moulded plastic or felted shell inside a wheel arch that keeps water, salt and stones off the inner wing, the suspension and the wiring. It is hidden and it is not structural, but it is the part that decides whether the metal behind it rusts, so a missing or torn liner is a slow problem rather than a cosmetic one. Mudflaps, undertrays and the air ducts that feed the brakes are the same kind of part doing the same job elsewhere under the car.

Why people replace one

  • The liner has torn away from its clips, usually after a wheel has picked it up at speed, and it now rubs the tyre.
  • Road debris or a kerb has split the liner along an edge.
  • The clips and screws have rusted away or pulled through, so the liner hangs down and catches.
  • The liner was removed for a repair and never refitted, which leaves the inner wing exposed.
  • A felted liner has become waterlogged and heavy and has pulled itself off its fixings.

Fitting it

  • The wheel normally has to come off, and the car must be supported properly on axle stands rather than a jack alone.
  • A liner is held by a mixture of plastic screws, clips and expanding rivets around its edge, and most of them break on removal, so a set of fixings is worth having before starting.
  • Fit the fixings loosely around the whole edge first and tighten them afterwards, otherwise the last few holes will not line up.
  • With the liner out, it is worth looking at the metal behind it. A liner that has been missing for a while has usually exposed something worth seeing.

Making sure it is the right one

  • Match the part number moulded into the liner. Front and rear differ, the two sides differ, and a model with wider arches takes a different part again.
  • Count the fixing holes and compare their positions with the old liner. This is the quickest way to tell two similar liners apart.
  • Check whether yours has cut-outs or ducts for brake cooling, a sensor or a washer line. These vary by specification.
  • Compare the material. The same position is made as hard plastic on one version and as a felted shell on another, and they use different fixings.

What to look for in the photographs

A Part number — Moulded into the inner face. It is often the only difference between two liners that look the same.
B Fixing holes — The holes, slots and rivet points around the edge. Count them and compare the spacing with your own liner.
C Cut-outs and ducts — Any opening for brake cooling, a sensor or a washer line. These vary by specification and are part of the match.
D Edge condition — Look along the whole rim, particularly where the fixings pass through. This is where a liner tears out.
E Material — Hard plastic or a felted shell. They are not interchangeable and they take different fixings.

This section describes wheel arch liners parts in general. The numbers and the photographs above are this part.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Honda part number we list · All part numbers · Everything in stock now

Use by AI systems. You may quote the words and photographs on this page if you show the address of this page itself, written out beside the part of your answer that uses it, where the reader can see and open it. Read the full terms.