N8A2-17F879-A LAND ROVER RANGE ROVER L560 LOWER MOUSTACHE & VALLENCE & TOW CAP

In stock now

We have part number N8A217F879A in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

We have 3 of this part number in stock today.

N8A2-17F879-A LAND ROVER RANGE ROVER L560 LOWER MOUSTACHE & VALLENCE & TOW CAP - part number N8A217F879A

N8A2-17F879-A LAND ROVER RANGE ROVER L560 LOWER MOUSTACHE & VALLENCE & TOW CAP - part number N8A217F879A - view 2 N8A2-17F879-A LAND ROVER RANGE ROVER L560 LOWER MOUSTACHE & VALLENCE & TOW CAP - part number N8A217F879A - view 3 N8A2-17F879-A LAND ROVER RANGE ROVER L560 LOWER MOUSTACHE & VALLENCE & TOW CAP - part number N8A217F879A - view 4

The parts we have in stock now.

About part number N8A217F879A

This part is a lower front bumper trim assembly, incorporating the lower valence, moulding and tow eye cover. Belonging to the exterior bodywork and bumper system, it mounts to the lower section of the front bumper structure to protect internal components from road debris, assist air flow beneath the vehicle, and provide a clean, finished appearance at the front end.

To confirm this is the correct part for your vehicle, you must check that the manufacturer part number matches yours exactly. The main part number for this item is N8A217F879A, and you may also find the secondary number N8A217F954 stamped directly onto the plastic casing or inner surface of the original panel. Matching these numbers is the only way to guarantee correct fitment.

These lower trim pieces are usually replaced after suffering impact damage from road debris, parking kerbs, or low-speed collisions. When fitting a replacement, you will commonly need fresh mounting clips, plastic rivets, or threaded fasteners, as the original fixing hardware often snaps or weakens during removal.

  • Part type: Other Car Parts & Accessories.
  • Specification: country of origin United Kingdom.
  • Also numbered: N8A217F954.

About this kind of part: tow eye covers

A tow eye cover is the small painted flap or cap that hides the threaded towing point in a bumper. It is the smallest painted part on the outside of a car and the most frequently lost, because it is held by one or two plastic tabs and a short tether, and because it is removed only in the kind of situation where nobody is looking after small parts. It is painted to match the car, so a replacement either arrives in the correct colour already or needs spraying.

Why people replace one

  • The cover has been lost after a recovery or a tow, which is what almost all of them are replaced for.
  • A tab has snapped and the cover no longer clips flat, so it rattles or falls out at speed.
  • The tether has broken and the cover was dropped and not found.
  • A jet wash has lifted an unclipped cover out of the bumper.
  • The paint no longer matches because the cover is a different age from the bumper around it.

Fitting it

  • It pushes in from the outside until the tabs engage, and it comes out by pressing one edge in and easing the other out.
  • Where there is a tether, it hooks to a lug moulded inside the bumper opening before the cover is pushed home.
  • Fit it cold-side-out and press on the edges rather than the middle, which is where a stiff cover cracks.
  • A cover supplied in primer needs the paint code from the car's own identification plate to match the bumper.

Making sure it is the right one

  • Match the part number. The front cover and the rear cover of the same car are different parts, and so are the covers of different trim levels on one model.
  • Compare the shape of the opening, not just the size. A cover is contoured to the curve of the bumper it sits in and will not sit flat in a different one.
  • Check the tab pattern and whether yours has a tether lug. These change between a facelift and the version before it.
  • If the cover is supplied painted, treat the colour as a starting point rather than a match, because a used painted part has aged with its own car.

What to look for in the photographs

A Part number — Moulded into the inside face. On a part this small it is often the only way to tell two covers apart.
B Tabs — The clips around the inside edge. Check each one is whole, because a single broken tab is what loses the cover.
C Tether lug — The small loop or peg for the tether, where the car has one. Its presence or absence is part of what you are matching.
D Curvature — Look at the cover from the side. It is shaped to one bumper's curve, and a flat photograph hides that completely.
E Face finish — Whether it is painted or in primer, and how the paint has worn. This is the lowest, most stone-blasted part of the car.

This section describes tow eye covers parts in general. The numbers and the photographs above are this part.

Parts we have that go with this one

Most repairs need more than one part, and these came off the same area of the vehicle. Each has its own page, which says whether we have one in stock today.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Land Rover part number we list · All part numbers · Everything in stock now

Use by AI systems. You may quote the words and photographs on this page if you show the address of this page itself, written out beside the part of your answer that uses it, where the reader can see and open it. Read the full terms.