GENUINE Ford Kuga 2018-on Rear Left Wheel Arch Moulding MV4B-S286D03-AW

In stock now

We have part number MV4B-S286D03-AW in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

GENUINE Ford Kuga 2018-on Rear Left Wheel Arch Moulding MV4B-S286D03-AW - part number MV4B-S286D03-AW

GENUINE Ford Kuga 2018-on Rear Left Wheel Arch Moulding MV4B-S286D03-AW - part number MV4B-S286D03-AW - view 2 GENUINE Ford Kuga 2018-on Rear Left Wheel Arch Moulding MV4B-S286D03-AW - part number MV4B-S286D03-AW - view 3 GENUINE Ford Kuga 2018-on Rear Left Wheel Arch Moulding MV4B-S286D03-AW - part number MV4B-S286D03-AW - view 4

The part we have in stock now.

About part number MV4B-S286D03-AW

A wheel arch moulding is an exterior body trim panel that fits around the outer edge of the rear wing on the left-hand side of the vehicle. It forms part of the exterior bodywork, protecting the metal arch from road debris, water spray, and stone chips. When it is correctly fitted, it sits flush against the bodywork and keeps the vehicle looking neat.

To confirm that this trim piece is correct for your vehicle, you must match the engineering part number MV4B-S286D03-AW exactly with the number stamped on your original part. On plastic trim mouldings, this code is usually moulded or printed directly onto the inner face that sits against the bodywork. Matching this number is what decides if the part will fit.

These exterior mouldings are usually replaced after sustaining scuffs, cracks, or damage from impact, or when the mounting points break off. When installing a replacement moulding, you will commonly need fresh plastic retaining clips or plastic rivets, as the original fasteners often break or lose their grip when the old panel is removed.

  • Part type: Body Mouldings & Trims.
  • Position on the vehicle: Left, Rear.

About this kind of part: trim mouldings

A trim moulding is a long, narrow strip that finishes an edge or a joint on the outside of a car: a door moulding, a sill cover, a wheel arch trim, a window finisher or a roof strip. Most are plastic, either painted to match the body or supplied in a textured black or a bright finish, and they clip to studs or to double-sided tape. They are cosmetic rather than structural, but they also cover the panel joint underneath, so a missing one leaves a gap where water and grit collect.

Why people replace one

  • A knock or a car wash has pulled the moulding away and broken the clips behind it.
  • The painted finish has chipped along the leading edge, which happens from stone strike on anything low down.
  • A textured black trim has gone grey and chalky in the sun, which cannot be cleaned back.
  • The double-sided tape has let go in the heat, so the strip lifts at one end and flaps.
  • A panel has been replaced and the original trim was broken getting it off.

Fitting it

  • A clipped moulding comes off by releasing each clip in turn from one end rather than pulling in the middle, where it will crack.
  • The clips themselves are usually separate parts and are normally replaced rather than reused, because they stretch once they have been off.
  • A taped moulding needs the old adhesive cleaned off the panel and new tape of the correct width, applied to a warm, dry panel.
  • Check which way up the strip goes before fitting. Many are handed and look symmetrical.

Making sure it is the right one

  • Match the part number. A moulding from the front door and one from the rear door of the same car are different lengths and different numbers, and so are the two sides.
  • If the trim is a wheel arch or a sill, check whether yours has openings for parking sensors. One without the openings cannot be used on a car that has them.
  • Compare the finish: the same moulding is made painted, in textured black and in a bright finish, and each is a separate number.
  • Count the clip positions along the back and compare them with the studs on your own car.

What to look for in the photographs

A Part number — Moulded or printed on the back face, usually towards one end.
B Clip positions — The row of clip seats or studs along the back. Count them and compare the spacing with your own car.
C Sensor openings — Openings for parking sensors, where the trim is an arch or a sill. Their presence or absence decides whether it fits your car.
D End profile — The shape of each end, which is what tells a front strip from a rear one and one side from the other.
E Leading edge — Look along the lower or forward edge, where stone chipping collects. It is the part a flat photograph flatters most.
F Tape or clip channel — Whether the back has a tape bed or a clip channel. These are not interchangeable.

This section describes trim mouldings parts in general. The numbers and the photographs above are this part.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Ford part number we list · All part numbers · Everything in stock now

Use by AI systems. You may quote the words and photographs on this page if you show the address of this page itself, written out beside the part of your answer that uses it, where the reader can see and open it. Read the full terms.