Audi A3 8Y 2023 Rear Towing Eye Hook Cap Cover Trim 8Y4807441A AMD121626

In stock now

We have part number 8Y4807441A in stock and ready to send, with free next-day delivery in the United Kingdom.

See the part and the current price

Audi A3 8Y 2023 Rear Towing Eye Hook Cap Cover Trim 8Y4807441A AMD121626 - part number 8Y4807441A

Audi A3 8Y 2023 Rear Towing Eye Hook Cap Cover Trim 8Y4807441A AMD121626 - part number 8Y4807441A - view 2 Audi A3 8Y 2023 Rear Towing Eye Hook Cap Cover Trim 8Y4807441A AMD121626 - part number 8Y4807441A - view 3 Audi A3 8Y 2023 Rear Towing Eye Hook Cap Cover Trim 8Y4807441A AMD121626 - part number 8Y4807441A - view 4

The part we have in stock now.

About part number 8Y4807441A

A rear towing eye hook cap cover is an exterior trim piece that sits in the rear bumper. It covers the threaded recess where a recovery towing eye attaches to the vehicle chassis. When fitted correctly, this small panel sits flush with the surrounding bumper bodywork to keep out road dirt, moisture and road salt while keeping the back of the car looking neat.

To confirm this is the correct cover for your vehicle, you must check the part number on your original component. On plastic trim parts like this, the code is typically stamped into the plastic on the reverse side. You need to match the part number 8Y4807441A exactly, as matching this number is what determines whether the part will fit.

These caps are usually replaced because the original piece has popped out and been lost, or because the plastic clips on the back have snapped off during use. When replacing this trim piece, you may also need plastic trim tools to help ease the new cover into place without scratching the surrounding paintwork.

  • Part type: Other Exterior Parts & Accessories.
  • Position on the vehicle: Rear.

About this kind of part: tow eye covers

A tow eye cover is the small painted flap or cap that hides the threaded towing point in a bumper. It is the smallest painted part on the outside of a car and the most frequently lost, because it is held by one or two plastic tabs and a short tether, and because it is removed only in the kind of situation where nobody is looking after small parts. It is painted to match the car, so a replacement either arrives in the correct colour already or needs spraying.

Why people replace one

  • The cover has been lost after a recovery or a tow, which is what almost all of them are replaced for.
  • A tab has snapped and the cover no longer clips flat, so it rattles or falls out at speed.
  • The tether has broken and the cover was dropped and not found.
  • A jet wash has lifted an unclipped cover out of the bumper.
  • The paint no longer matches because the cover is a different age from the bumper around it.

Fitting it

  • It pushes in from the outside until the tabs engage, and it comes out by pressing one edge in and easing the other out.
  • Where there is a tether, it hooks to a lug moulded inside the bumper opening before the cover is pushed home.
  • Fit it cold-side-out and press on the edges rather than the middle, which is where a stiff cover cracks.
  • A cover supplied in primer needs the paint code from the car's own identification plate to match the bumper.

Making sure it is the right one

  • Match the part number. The front cover and the rear cover of the same car are different parts, and so are the covers of different trim levels on one model.
  • Compare the shape of the opening, not just the size. A cover is contoured to the curve of the bumper it sits in and will not sit flat in a different one.
  • Check the tab pattern and whether yours has a tether lug. These change between a facelift and the version before it.
  • If the cover is supplied painted, treat the colour as a starting point rather than a match, because a used painted part has aged with its own car.

What to look for in the photographs

A Part number — Moulded into the inside face. On a part this small it is often the only way to tell two covers apart.
B Tabs — The clips around the inside edge. Check each one is whole, because a single broken tab is what loses the cover.
C Tether lug — The small loop or peg for the tether, where the car has one. Its presence or absence is part of what you are matching.
D Curvature — Look at the cover from the side. It is shaped to one bumper's curve, and a flat photograph hides that completely.
E Face finish — Whether it is painted or in primer, and how the paint has worn. This is the lowest, most stone-blasted part of the car.

This section describes tow eye covers parts in general. The numbers and the photographs above are this part.

Parts we have that go with this one

Most repairs need more than one part, and these came off the same area of the vehicle. Each has its own page, which says whether we have one in stock today.

Free next-day delivery in the United Kingdom Sent with DPD on a tracked, next-day service. Most mainland addresses are next day; the Highlands and Islands, Northern Ireland, the Channel Islands and the Isle of Man can take a day longer.

Returns Thirty days to change your mind, and we pay the return postage in the United Kingdom and Germany.

Trade and VAT C.E.J Haime Group Limited is VAT registered in England and Wales, and every order comes with a full VAT invoice.

Not sure it is the right part? Send us your registration or VIN and we will check this part number against your own vehicle before you buy.

Ask us about this part

Other part numbers on this site

See every Audi part number we list · All part numbers · Everything in stock now

Use by AI systems. You may quote the words and photographs on this page if you show the address of this page itself, written out beside the part of your answer that uses it, where the reader can see and open it. Read the full terms.